This internet browser is outdated and does not support all features of this site. Please switch or upgrade to a different browser to display this site properly.
The Department of Electrical and Computer Engineering features well-equipped facilities that enhance teaching, research, and practical learning across electrical engineering, computing, and networking disciplines.
Automated Wind Power Generator WG/EV, Sys for Indoor Operation Wind Power Generator WG-1/EV, Outdoor 12V, 400W wind turbine with M.S Steel pole installed on concrete base – Wind energy testing
Custom made static/dynamic tracking solar system with an outdoor unit of 100W solar panels, 5KW Afore Single Phase on grid solar PV Inverter – Solar energy testing
Solmetric PVA-1000 PV Analyzer Kit – Solar irradiance testing
Custom made Micro Hydro Plant for indoor Renewable Energy Lab – Micro hydro energy testing
DS1104 PPC 603E/250MHZ DSPACE Controller Board – Used for simulation
Chroma 62150H-600S – Programmable DC power supply.
Protective Relaying Training System 8007 (Labvolt) – Power system relay protection studies includes Four-Quadrant Dynanometer, Syncronous Motor/Generator, Faultable Transformer Module
SEL-311C, 487B & 487E Protection Relay – Distance protection, bus differential and breaker failure relay, transformer protection relay
Motor Education Kit with ABB Himan Machine Interface CP607; ABB IE2, 1.5 KW Cast Iron Motor – Used for induction motor and variable frequency speed drives
Secondary Current Injection – T&R 50 amp 3 phase SCITS, (50A-3PH mk2) – Used for current injection testing
FLUKE 43B Power Quality Analyser – Used for power quality testing
U1452A Handheld Insulation Tester (Keysight) – Used for insulation resistance testing and electrical safety assessment
U5855A G1 Thermal Imager (Keysight) – Used for thermal imaging and temperature distribution analysis
U2351A Process Data Acquisition (Keysight) – Used for process monitoring, signal measurement, and data acquisition applications
U1401B Handheld Process Calibrator (Keysight) – Used for process calibration and instrumentation testing
N2891A Differential Probe 70MHz (Keysight) – Used for voltage measurement and differential signal testing
N2783B Current Probe, 30A AC/DC, 100MHz (Keysight) – Used for AC/DC current measurement and electrical analysis
DSOX2012A Oscilloscope, 2 Channel, 100 MHz – Used for waveform observation, signal analysis, and electronic circuit testing
U1604B 40MHz Handheld Oscilloscope (Keysight) – Used for portable waveform measurement and troubleshooting applications
U1233A Electrical Handheld DMM (Keysight) – Used for electrical measurement and digital multimeter applications
Goodwill GFG-8020G Function Generator – Used for generating electronic test signals and waveform simulations
Goodwill GPC-3030 Dual Tracking Power Supply – Used for supplying regulated DC power for electronic and laboratory experiments.
FPGA Development System (Quartus II with VHDL) – Used for designing and implementing digital circuits such as logic gates, counters, and registers using VHDL programming in the Quartus II environment.
Siemen TIA portal – PLC programming
Electronic testing boards – Op-amp, Diode and BJT
Cisco Series Routers – Used for conducting CCNA courses (Model including 1941, 2811, 2911, 2901, and 2901-K9)
Cisco ISR 4000 Series – Used for learning and applying various security features in different layer of TCP/IP protocol stack. Also used for analyzing types of cyber attack and malwares and mitigating those attacks (Model including 4221-K9 and 4321-K9)
Cisco Ethernet Router 2620 10/100
Cisco Catalyst Switches – Model including Cisco Catalyst Switch 12 Port, Cisco Catalyst Switch 2961 10/100 + 2 1000BT LAN Base Image, Cisco Catalyst Switch 2960 Plus 24 10/100 + 2T/SFP LAN Base, Cisco Catalyst Switch 2960 Plus 24 10/100 POE + 2 T/S
Cisco Wireless Controllers – Used for conducting wireless data network course (Model including 2100 Series and 2500 Series)
